AIR-RC

Novice-III V2 from Eachine

Details

Features:

New toothpick F4 flight controller
Internal SPI Frsky D8/D16 receiver (Dual antenna and with PA)
Powerful and smoothly and long flight time (about 8~10 Mins)
Led Strip ready
Built-in Buzzer ready
New design 1203 KV5500 motors
Camera Angle adjustable
VTX power switchable 25mw~400mw
Smartaudio ready , change VTX bands, powers, channels via OSD
720P DVR ready (Analog 1280*720)
Real Ready to fly
Compatible both for 2s-3s Lipo/LIHV

Pictures

Radio icons

FrSky X10

FrSky X12s

Jumper T16

Jumper T18

Radiomaster TX16S

FlySky NV14

FlySky EL18

PNG (192x114)

FrSky X9D

FrSky X9E

BMP (64x32)

FrSky X20

FrSky X20 Pro

FrSky XE

Kavan V20

PNG (300x280)

BMP Recommended (300x280)

FrSky X18

FrSky Twin

PNG (180x166)

BMP Recommended (180x166)

FrSky X10

FrSky X12s

PNG (180x160)

BMP Recommended (180x160)

FrSky X10

FrSky X12s

JPG (155x100)

Futaba 18MZ

JPG (158x80)

Graupner MZ16

Graupner MZ32

BMP (158x106)

Jeti DS-24

PNG (320x240)

Spektrum ix12

Spektrum ix20

JPG (266x164)

Similar Models

Some content in menu 2.

We cannot guarantee that the shops listed below do sell the Novice-III V2 in particular but at least we know they do distribute Eachine.

Where to buy

Hungary
SG RC Modell
check web site
Ship to: Hungary

Ireland
Radio Controlled Shop
check web site
Ship to: Ireland

Hong-Kong
Banggood
check web site
Ship to: International

Wingspan: 135mm (5.3 in)
	Length: 135mm (5.3 in)
Weight: 62 g (2.2 oz)

See Specs & Tech Details

Wheelbase: 135mm
Size: 115mm*110mm*40mm
Weight: 62g(without battery)

Motor	Mode: EX1203 KV options: KV5500 Configu-ration:9N12P Stator Diamter:15mm Stator Length:3mm Shaft Diameter: Φ1.5mm Motor Dimension(Dia.Len):Φ15mm15mm Weight(g):4.5g
Flight controller	MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 2-4S battery input (DC 8V-17V) Built-in 10A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Frsky D8/D16 SPI receiver Built-in 2.4G Power Amplification Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 70A Built-in 5V 1.5A BEC Built-in voltage detection
Onboard 4in1 ESC	MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Current: 10A continuous peak 12A (5 seconds) Support BLHeliSuite programmable Factory firmware: F_H_40_REV16_7.HEX Default protocol: DSHOT600
Internal Frsky NON-EU receiver Version	SPI BUS receiver Frsky D8/D16 compatible Compatible Non EU transmitter both D8 mode and D16 mode Channels: 8ch/16ch Dual antenna Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 400m
VTX&DVR	Output power: 25~400mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 400mA(type) Antenna: RG178 antenna Frequency: 5.8GHz 5bands 40 channels With Raceband Smartaudio ready Weight:3.4g
Caddx EOS2	1/3" CMOS Sensor 1200 TVL 2.1mm lens 4:3 Image size NTSC Global WDR Internal Synchronization
Lipo Battery	Capacity:450mAh Voltage:11.4v Continuous Discharge Rate: 75C Size: 66mmx21mmx18mm Weight: 42g Connector: XT30
Eachine EV800 Goggles	Screen size: 5.0 inch Screen resolution: 800*480 (No blur after enlarge by the lens) Screen brightness: 600cd/m2 with special high brightness backlight LED for outdoor FPV View Angle: 140/120 degree(Horizontal/Vertical) 3x boost of the video to acquire intense feel-in-there video 92% transparent rate no distort of light Built-in 3.7V/2000mAh battery Each battery circle offer around 3.5hr working time 5-12V wide recharging voltage range, typical recharging voltage is 5V Accepts 5V power banks or 2S(7.4V)/3S(11.1V) battery as back-up power to have long working time
Eachine ER8 2.4G Radio	Brand Name:Eachine Frequency:2.4Ghz Channels: 8 Mode: Mode 2 Firmware: OPENTX 2.19 Working voltage:7.4v~12v Frsky D8 receiver compatible

4,522 models

(54,264 icons in the database)

ASK FOR A NEW MODEL TO BE ADDED

Although I do my best to complete this library, you may not find the model you are looking for.

In this case, do not hesitate to ask me to add it : You're not bothering me. Please be patient, depending on my workload, I may take a few days to work on your model and gather information.

Ask for a new model

Generate your own image