Projeti 2 Red Edition from Ideecon


The lively Projeti2 thrilled by both his fast-paced flight (measured speed of over 200 km / h), as well as by his good-natured slow-flying characteristics (lands at a pace of walking). The low flying weight, the sophisticated aerodynamics and the high efficiency of the pressure propeller drive give the Projeti a very high performance potential that has characterized the Projeti for years.
We have adapted the Projeti to the new wishes and requirements and foam the model in the new EPO show. We additionally reinforced the model by foaming a carbon fiber reinforcing tube in the production process. This ensures that the Projeti can withstand extreme maneuvers even when the engine is hot.

A 6 mm carbon tube with over 300 mm length is foamed directly into the wing and gives the Projeti an enormous strength. This makes it almost unbreakable in flight!

A laser-cut aluminum motor mount with two motor-length stops gives the Projeti a high strength at the fuselage-stern and allows the assembly of BL internal rotor with 28 mm diameter to max. 45 mm length too. The engine mount dissipates additional heat from the engine and is already glued to the foam as standard. The servo bays were enlarged to 29 x 28 x 15 mm for the installation of larger and larger servos.

The redesigned, highly visible Projeti 2 Decorsatz differs well from top and bottom and contributes to good attitude detection. Fuselage nose and fuselage back are painted inline to fit the decor set and are already contour-cut to ready-to-install. (For illustration, part photos of the predecessor model)


  • One-piece fuselage/wings made of EPO* foam in white foam.
  • A 6 mm carbon tube over 300 mm long is directly foamed into the wing and gives the Projeti enormous strength. This makes it almost "unbreakable in flight!
  • A laser-cut aluminium motor mount with two motor length stops gives the Projeti2 high strength at the rear fuselage and allows the installation of BL internal rotors with 28 mm diameter up to a maximum length of 45 mm.
  • The engine mount additionally dissipates heat from the engine and is bonded to the foam as standard.
  • The servo shafts have been enlarged to 29 x 28 x 15 mm for the installation of larger and stronger servos.
  • NEW coloured decor printed on special foil.
  • Tail fins made of contoured balsa wood.
  • Fuselage back, canopy and nose made of impact-resistant PEG plastic, painted inline and contour milled ready for installation.
  • Complete rudder linkage, rudder horns made of GRP.
  • Extensive illustrated building instructions.


Radio icons

FrSky X10

FrSky X12s

Jumper T16

Jumper T18

Radiomaster TX16S

FlySky NV14

FlySky EL18

PNG (192x114)

FrSky X9D

FrSky X9E

BMP (64x32)

BMP (64x32)

FrSky X20

FrSky X20 Pro

FrSky XE

Kavan V20

PNG (300x280)

BMP Recommended (300x280)

FrSky X18

FrSky Twin

PNG (180x166)

BMP Recommended (180x166)

FrSky X10

FrSky X12s

PNG (180x160)

BMP Recommended (180x160)

FrSky X10

FrSky X12s

JPG (155x100)

Futaba 18MZ

JPG (158x80)

Graupner MZ16

Graupner MZ32

BMP (158x106)

Jeti DS-24

PNG (320x240)

Spektrum ix12

Spektrum ix20

JPG (266x164)

Similar Models

Some content in menu 2.

We cannot guarantee that the shops listed below do sell the Projeti 2 Red Edition in particular but at least we know they do distribute Ideecon.

Where to buy

Wingspan: 820mm (32.3 in)
Length: 534mm (21 in)

Weight: 700 g (1.5 lbs)
Wingspan: 820 mm
Flight weight approx. (g): 700 g
Empty weight approx. (g): -
Control: H,Q,M
Length (mm): 534
Fuselage: EPO
Wings: EPO
Rec. engine: BL Outrunner
Rec. Battery: 3S-4S LiPo 1800-2200mAh

Box Content:

  • Carbon fibre reinforcement tube already foamed in
  • Attractive decor set contributes to good flight attitude recognition
  • Laser-cut aluminium engine mount, fully assembled

Other Variant(s)

4,640 models
(55,680 icons in the database)

Although I do my best to complete this library, you may not find the model you are looking for.

In this case, do not hesitate to ask me to add it : You're not bothering me. Please be patient, depending on my workload, I may take a few days to work on your model and gather information.

Ask for a new model

Generate your own image


C-130 V2
Eternity F5J
P-51 Voodoo
Pug Twisty

A simple 'thank you' or a kind message is my first salary but if you think this website is useful, if you like the content, the service and if you want to participate to the hosting, feel free to donate. I thank you in advance.

Read me
Recent Changes
AIR-RC is the largest online database about RC Model Flying and it's growing...
Each model has descriptions, specifications, photos, video, icons for your radio and links to shops and manufacturers.
We sell nothing, it's made by RC hobbyist for RC hobbyists. Enjoy !
Copyright AIR-RC © 2024