Infusion 600n Platinum from TSA Model

Details

  • Complete metal rotor head ensures maximum strength and durability. Extra large in design for high head speed aggressive 3D flying style, designed for today with tomorrows capability. Extra large ball links and push rod allowing the rotor head to pivot for a direct and smooth feel at all rotor head speeds. 12mm main shaft is leading the class in today’s 600 sized helicopters. Integrated pivot ball and internal guides ensures the rotor head motion is in a pivot motion only. Providing increased pitch and cyclic response and stability.
  • Front and rear gyro mount standard on all models. Ensuring your gyro or remote gyro sensors is located in an area of low vibration.
  • Extra large polymer impregnated metal plastics gears have been used extensively throughout. Full metal construction increases strength and provides consistent gear mesh for a smooth gear train. Dual radial bearings and a single thrust bearing are installed in each rotor grip for maximum precision and performance. A hard anodized aluminium pitch slider with dual bearing is also included for weight reduction and durability. Dual ball bearings are moulded directly into the pitch links for increased precision and simplicity.
  • Large diameter boom supports with supporting M4 bolts for superior rigidity. Eliminating boom flex providing a direct tail rotor feel with precise start and stop characteristics during rotation. Ball raced tail bell crank along with carbon fibre push rod providing a smooth flex free operation. The tail servo is placed in front of the engine in a position free from nitro oil while optimizing the centre of gravity of the nitro version.
  • Eliminating servo movement is critical with flybarless models. A key TSA feature is our innovating servo brace which eliminates all servo output shaft bending stress and flex. This ensures your gyro input is going directly to the rotor head and not in unwanted servo movement. Our servo support also ensures the greatest chance your servos are safe in the event of a crash.
  • Servo performance is key to the performance of your model and TSA has revolutionised servo layout with its Infusion series. All servos are high in the frame ensuring the centre of mass is as close as possible to the rotor head for increased performance. Direct push/pull elevator servo layout with carbon fibre linkage rods provides a highly precise system.
  • Included in all kits is our fully adjustable boom support brace. High lateral loads are transmitted from the tail rotor to the boom supports. This load then results in bending force on the boom and mainly the boom supports. Our brace ensures the bending stress is minimized by locking the 2 supports together forming a truss style arrangement. Tail stiffness is critical to the performance of your tail gyro and this is one key area many overlook.
  • TSA has taken the thinking out of wiring. This area is normally over looked by all and dreaded by most builders. This thankfully is a thing of the past for all you TSA flyers. Included in all kits are rubber moulded grommets protecting your servo wires from rubbing on carbon fibre. This rubbing effect and flapping wires is then eliminated by a multiple selection of wire clamps. Included are single and double servo wire and single servo wire with circular remote gyro wire clamps. We have covered all possible installations, just clip in and enjoy.
  • Class leaders by design TSA has innovated the anti rotation swashplate feature into our direct 8 bearing elevator assembly. Keeping your swashplate rigid ensure the phasing is maintained at 120 degree. This ensures the pilot input is sent directly to the rotor head.
  • Frame stiffness is critical to a helicopter as unwanted movement can be transmitted to the gyro system controlling both the tail rotor and rotor head. TSA has integrated X braces with centralised location points providing a 6 point location on each brace. Our wide frame design along with X brace technology provides and extremely rigid helicopter which is fast to build and very resistant to high impact crash damage normally seen by most other models.
  • An extremely rigid wide frame design with integrated X brace frame stiffeners ensures a low vibration and extremely strong flying model. Polymer impregnated metal plastics used for increased stiffness and weight saving.
  • Large 650ml tank with moulded rubber dampers to minimise vibration and fuel foaming. TSA Patent Pending fuel pickup system “Fuel Addict” shrouded foam intank pick is also included on all nitro and gas models. Get every last drop from your tank TSA has the solution.

Pictures

Manual


If the Manual doesn't show you can click here to open the document in a new window.

Radio icons

FrSky X10

FrSky X12s

Jumper T16

Jumper T18

Radiomaster TX16S

FlySky NV14

FlySky EL18

PNG (192x114)

FrSky X9D

FrSky X9E

BMP (64x32)

BMP (64x32)

FrSky X20

FrSky X20 Pro

FrSky XE

Kavan V20

PNG (300x280)

BMP Recommended (300x280)

FrSky X18

FrSky Twin

PNG (180x166)

BMP Recommended (180x166)

FrSky X10

FrSky X12s

PNG (180x160)

BMP Recommended (180x160)

FrSky X10

FrSky X12s

JPG (155x100)

Futaba 18MZ

JPG (158x80)

Graupner MZ16

Graupner MZ32

BMP (158x106)

Jeti DS-24

PNG (320x240)

Spektrum ix12

Spektrum ix20

JPG (266x164)

Similar Models

Some content in menu 2.

We cannot guarantee that the shops listed below do sell the Infusion 600n Platinum in particular but at least we know they do distribute TSA Model.

Where to buy


Wingspan: 1345mm (53 in)
Length: 1345mm (53 in)

Weight: 3540 g (7.8 lbs)
Full length of fuselage 1230mm    
Full width of fuselage 215mm    
Height 390mm    
Main blade 600 ~ 620mm    
Main rotor diameter 1345mm    
Tail blade 90mm    
Tail rotor diameter 252mm    
Main gear ratio 14T : 122T    
Tail gear ratio 113T : 25T    
Gear ratio 8.7 : 1 : 4.52    
Material specification Carbon fiber    
Tail rotor drive shaft drive    
Swashplate angle 120°    
Fullweight( approx) 3540g    
Engine class 50 ~ 55 Nitro    
Full tank capacity 650cc    
Material specification Carbon fiber    
Tail rotor drive shaft drive    
Swashplate angle 120°    
EnglishFrenchGermanItalianPortugueseRussianSpanish
4,769 models
(57,228 icons in the database)
ASK FOR A NEW MODEL TO BE ADDED

Although I do my best to complete this library, you may not find the model you are looking for.

In this case, do not hesitate to ask me to add it : You're not bothering me. Please be patient, depending on my workload, I may take a few days to work on your model and gather information.

Ask for a new model

Generate your own image

RANDOMIZER

Nazgul5 V3 O3
Sopwith Camel F1
CineLog30
Sbach 342 50E
FRSKYX14_2312
PENGUIN_2307
X20AWE_2403
GOGGLEX_2311
CINELOG25_2310
ALTUS_2404
NOTE

A simple 'thank you' or a kind message is my first salary but if you think this website is useful, if you like the content, the service and if you want to participate to the hosting, feel free to donate. I thank you in advance.

Information
Read me
Recent Changes
AIR-RC is the largest online database about RC Model Flying and it's growing...
Each model has descriptions, specifications, photos, video, icons for your radio and links to shops and manufacturers.
We sell nothing, it's made by RC hobbyist for RC hobbyists. Enjoy !
AIR-RC
Copyright AIR-RC © 2024